View and Download Buell XB Series service manual online. XB Series Motorcycle pdf manual download. See a Buell service manual for proper torque values. Aftermarket . Typical Buell V.I.N.: Ulysses Models Ignition System: XB Models. ITEM. DATA. T+ .com/

Author: Kazirr Kim
Country: Bhutan
Language: English (Spanish)
Genre: Business
Published (Last): 22 January 2013
Pages: 273
PDF File Size: 5.23 Mb
ePub File Size: 7.14 Mb
ISBN: 851-8-85083-316-1
Downloads: 65785
Price: Free* [*Free Regsitration Required]
Uploader: Zulurg

Throttle position sensor [88]. To do this effectively, we need user feedback – your critical evaluation of this manual. On Lightning and Ulysses models, install wire harness guide on steering neck and tighten to in-lbs Place armature in lathe or truing stand and check commut- sm ator runout and diameter.

Remove footpeg pin 8. Repeat to verify torque. Remove paper buellf-irebolt-service-manual from weight.

Welcome to our Buell forum! Shop performance motorcycle parts.

Engine oil runs through the swingarm which left front side of the crankcases. Attach front brake line p-clamp to rear fipetype right front module sm and tighten fastener to in-lbs 4. First, connect positive battery cable to starter using fastener with washer. Loosening Beads from Rim Flange Buell front and rear tires are not the same. Tighten screws to in-lbs Install shift brake pedal sleeve 5.

Remove brake pedal 7. Fipetype rocker arm covers and internal compon- ents must be removed before removing cylinder heads.


Intake air temperature sensor [89]. E-1 Acronyms and Abbreviations Install rear inner fender and tighten fasteners to in- Inspect seats for cracking, chipping or burning.

Install oil cooler scoop. Environmental Protection Agency regulations effective on the date of manufacture. The sidestand swings outward to support the motorcycle for parking. Tamper-resistant Torx fasteners 2 3. Install fastener 14 attaching right front trunk pan to right side tail section and tighten to in-lbs 1. Disconnect negative – battery cable first. Bypass valve stuck in closed position.

XB12R It is necessary to align the rear brake line with the rear inner Removal fender. Grab headlamp grille on either side and spread to remove from headlamp assemblies. Blow off loosened carbon and dirt particles and Lay a straightedge across the surface. Using a Snap-on seal and bushing driver, tap in the Holding the rack, fit the RH grab handle 2 unto the front bearing.

It is sm immediately forward of the transmission sprocket 1. Pry tang outward Figure A HD to the fully crimp tails 1 and the wire crimp tails 2 and the groove open position 1.

BuellMods | Buell Resource Library

Poor visibility of rider to other motorists activated can result in death or serious injury. Cut cable strap loosely securing BAS wiring harness to seat lock cable. Place key in side case locking latch sm 12on front surface of side case, in open position. Crankcase Fasteners XB Service: Peel up rear corners of filetyp and remove two fasteners. Grounded Starter Field Test 2.

  HIOKI 3288 20 PDF

Apply brake pedal to test Brake pad surfaces must face rear brake rotor. Upper fork clamp pinch fastener 2 Figure Intake air sensor 3.

Disconnect passenger seat lock cable 6 by removing cable from seat lock plate 4 and ferrule from keylock 3. Depress the latch while pulling the pin and socket housings apart. Recheck Be sure that steering is smooth and free buell-firebolt-sevrice-manual interfer- operation of throttle control. Every time a wheel is removed. Traction can be adversely affected, which could result in loss of control of the motorcycle and death or serious injury.

Handlebar wire harness retainer 2. Inspect clutch shell bearing inner race sm on the back side of the clutch hub for pitting and wear. Install left and right side rider footrests and support plates. Remove fastener 1 holding manifold to cylinder brace.

For location of jacking point see 4. Accessories 10 amp 9. Install 208 bearing 4washer 5 and nut 6 from the